REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
AUGER HOUSING / IMPELLER ASSEMBLY
5
11
11
6
7
1
5
1
16
4
11
12
8
4
13
11
3
17
12
10
1
37
9
2
9
9
33
37
32
34
30
31
31
26
36
29
27
20
1
2
2
2
3
28
2
25
24
3
5
23
2
2
1
2
2
(EXPLODED)
18
19
01.07.026-F
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
20
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
AUGER HOUSING / IMPELLER ASSEMBLY
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
532 18 41-05 IMPELLER
532 42 71-48 GEARBOX ASSEMBLY
532 18 89-09 BEARING
532 42 71-46 IMPELLER PULLEY
532 44 24-38 DISCHARGE BASE
532 18 40-95 CORNER BRACKET
532 19 21-99 CLEAN OUT TOOL
532 40 54-00 TOOL CLIP
873 80 04-00 NUT 1/4-20
874 78 04-26 SCREW 1/4-20 X .625
532 42 79-42 NUT 5/16-18
532 16 31-83 SCREW 5/16-18 X .625
532 42 71-45 IMPELLER HUB
532 42 71-54 IMPELLER SLEEVE
532 14 52-12 FLANGE NUT 3/8-16
532 18 03-55 CARRIAGE BOLT
532 19 41-89 SCREW 13-16 X .625
532 40 77-60 PLUG
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
532 42 73-02 GEARBOX COVER RH
532 42 73-45 GASKET
532 40 77-70 SEAL
532 40 77-62 BEARING
532 17 46-97 THRUST WASHER 1.00
532 40 77-63 WORM GEAR
532 40 77-64 AUGER SHAFT
532 18 92-82 SQUARE KEY
532 40 77-58 BEARING
532 17 46-83 THRUST WASHER
532 42 71-47 IMPELLER SHAFT
532 18 42-05 ROLL PIN
532 17 46-81 THRUST WASHER
532 17 46-84 THRUST BEARING
532 40 77-69 BEARING
532 40 77-68 O-RING
532 40 77-67 SCREW 5/16-18 X .750
532 42 73-17 GEARBOX COVER LH
532 19 20-90 SHEAR BOLT
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
21
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
AUGER HOUSING / IMPELLER ASSEMBLY
1
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
532 43 88-28 AUGER HOUSING
532 40 78-25 SCRAPER BAR
872 27 05-05 CARRIAGE BOLT 5/16−18 X .625
532 15 53-77 NUT 5/16−18
3
(5x)
4
(5x)
2
01.07.001-A
2
1
KEY
NO.
PART
NO.
DESCRIPTION
1
2
532 42 10-72 AUGER ASSEMBLY LH 24
532 42 10-73 AUGER ASSEMBLY RH 24
01.07.017-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
22
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
AUGER HOUSING / IMPELLER ASSEMBLY
2
3
1
1
KEY
NO.
PART
NO.
2
DESCRIPTION
1
2
3
532 42 04-78 AUGER BEARING
532 41 19-39 BEARING PLUG
532 17 95-82 SCREW 5/16−18 X 1.00
3
01.07.024-B
4
3
2
3
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
532 18 40-93 SKID PLATE LH
4
1
532 18 40-94 SKID PLATE RH
872 27 05-06 CARRIAGE BOLT 5/16−18 X .75
532 42 79-42 NUT 5/16−18
01.11.001-C
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
23
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
CONTROL PANEL / CHUTE
11
KEY
NO.
PART
NO.
1
0
DESCRIPTION
2
3
5
1
2
3
4
5
6
7
532 44 42-39 CHUTE WELDMENT
532 43 88-32 DEFLECTOR WELDMENT
532 42 03-25 DEFLECTOR SEAL
532 18 41-14 STRAP
532 44 50-19 KNOB BLACK
532 12 84-15 POP RIVET
8
6
9
11
6
4
532 18 56-00 SHOULDER BOLT
11
1
/4−20 X .704
872 27 05-05 CARRIAGE BOLT
/16−18 X .625
8
9
5
7
532 19 17-30 NUT 1/4−20
1
10
11
12
13
532 15 54-15 WASHER
532 17 92-46 PLASTIC WASHER
532 43 03-24 CHUTE SNOW SHIELD
532 42 17-28 SHIELD RETAINER STRAP
6
13
2
1
01.09.005-E
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
24
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
CONTROL PANEL / CHUTE
2
2
1
*3
*7
*6
*4
01.09.010-B
*5
KEY
NO.
PART
NO.
DESCRIPTION
1
2
532 42 82-72 LEVER/CABLE ROTATOR ASSEMBLY
817 50 10-10 SCREW 10-24 X .625
532 42 06-78 ROTATOR HEAD
532 40 59-32 ROTATOR PIVOT BRACKET
532 42 06-75 PULLEY PIVOT
532 42 82-73 CABLE ASSEMBLY ADJUSTABLE
532 42 83-10 CABLE ASSEMBLY HEAT SHIELD
*3
*4
*5
*6
*7
NOTES:
. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.
1
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
25
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
HANDLES
5
1
10
6
KEY
NO.
PART
NO.
8
7
DESCRIPTION
2
1
2
3
4
5
6
7
8
9
532 42 10-69 PLOW HANDLE LH
532 42 10-70 PLOW HANDLE RH
532 42 91-48 PANEL BRACKET LH
532 42 91-49 PANEL BRACKET RH
532 19 95-13 HANDLE GRIP
874 78 05-12 SCREW 5/16−18 X .750
874 78 05-24 SCREW 5/16−18 X 1.50
532 75 11-53 NUT 5/16−18
5
3
9
8
6
7
8
9
4
532 15 54-15 WASHER
532 05 38-47 WASHER
10
01.08.003-B
1
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
5
532 42 15-36 LOWER HANDLE
2
532 44 36-17 PIVOT SUPPORT WELDMENT
817 00 05-10 SCREW 5/16−18 X .750
817 00 06-16 SCREW 3/8−16 X 1.00
532 85 10-74 WASHER HARDENED
4
3
4
5
4
4
5
3
01.05.013-C
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
26
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
HANDLES
10
2
11
4
7
8
9
9
5
7
6
1
12
3
13
14
8
14
12
13
1
2 13
14
13
14
01.08.002-J
12
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
532 41 55-39 CONTROL PANEL
580 68 78-02 CONTROL LEVER LH
580 68 77-02 CONTROL LEVER RH
532 41 55-46 TRACTION ROD ARM
532 42 90-98 IMPELLER ROD ARM
532 41 26-77 INTERLOCK BAIL
532 42 16-13 SPACER
532 16 96-75 RETAINER
817 06 04-10 SCREW 1/4-20 X .62
532 41 42-80 KNOB BLACK
532 41 42-81 KNOB RED
532 17 88-99 HANDLE KNOB
819 13 13-16 WASHER 3/8
10
11
12
13
14
872 12 06-18 CARRIAGE BOLT 3/8-16 X 2.25
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
27
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
HANDLES
2
10
KEY
NO.
PART
NO.
10
DESCRIPTION
1
2
3
4
5
6
7
8
9
580 79 77-01 IMPELLER ROD ASSEMBLY
580 79 79-01 TRACTION ROD ASSEMBLY
532 18 04-45 SHIFTER ROD TOP
532 18 77-16 SHIFTER ROD BOTTOM
532 18 04-47 SPRING SLEEVE
580 79 62-01 SPRING CONTROL ROD
580 80 21-01 SPRING TRACTION ROD
872 27 05-05 CARRIAGE BOLT 5/16-18 X .750
532 15 53-77 NUT 5/16-18
3
1
8
9
10
532 16 96-75 RETAINER
4
5
7
10
5
6
01.12.010-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
28
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
HANDLES
7
1
KEY
NO.
PART
NO.
3
6
DESCRIPTION
1
2
3
4
5
6
7
532 18 33-46 CONSOLE PANEL
532 17 86-68 HEADLIGHT BEZEL
532 18 09-27 FLOOD HEADLIGHT
532 18 44-71 SCREW 10−24 X .625
532 17 52-62 SCREW 10−24 X 1.25
532 44 50-29 WIRE HARNESS
532 18 37-84 BULB
4
2
5
5
4
01.10.003-D
4
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
5
6
532 41 62-88 INTERLOCK SPRING
532 44 52-91 INTERLOCK CAM
532 44 32-15 TORSION SPRING
532 16 96-75 RETAINER
817 06 04-10 SCREW 1/4−20 X .625
532 42 18-14 INTERLOCK STOP
3
2
5
1
01.08.007-D
6
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
29
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
DRIVE
ITEM 42 EXPLODED
2
46
45
1
16
48
51
17
18
4
7
15
14
15
49
12
9
50
20
22
1
1
11
24
5
3
9
0
1
19
9
8
1
3
1
53
23
1
34
4
52
5
3
7
21
6
24
5
33
23
53
3
31
0
3
3
3
29
3
2
28
38
26
3
5 53
27
24
26
36
4
3
37
42
44
43
54
39
2
25
4
2
41
40
39
01.02.013-C
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
30
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
DRIVE
KEY
NO.
PART
NO.
KEY
NO.
PART
NO.
DESCRIPTION
DESCRIPTION
1
2
3
4
5
6
7
8
9
532 19 88-75 SPEED SELECTOR ASSEMBLY
817 50 10-10 SCREW 10-24 X .625
532 43 88-37 END PLATE
817 49 05-08 SCREW 5/16-18 X .50
532 05 70-79 WASHER
532 40 54-85 CONTROL ARM
532 19 85-80 CLEVIS PIN
532 41 54-50 SHIFTER PLATE
532 40 28-81 SHOULDER BOLT
532 41 54-33 SHIFTER BRACKET
532 19 17-30 NUT 1/4-20
532 41 54-35 CLUTCH PLATE
532 41 68-64 CLUTCH BRACKET
532 18 71-01 SHIFTER LINK
532 70 02-79 RETAINER
532 42 75-42 CONTROL SHAFT
532 40 25-68 CLUTCH ROD
532 16 96-75 RETAINER
581 42 25-01 SHIFTER YOKE
532 40 23-10 PIVOT ROD
812 00 00-36 RETAINER
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
532 17 53-44 BEARING
532 17 86-13 WHEEL HUB
874 76 05-14 SCREW 5/16-18-.875
812 00 00-12 RETAINER RING
532 40 21-87 SPROCKET SHAFT
532 40 16-19 CHAIN
532 43 73-03 SPROCKET WELDMENT
532 41 54-29 SHIFTER BRACKET
532 18 01-35 SPRING
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
532 40 26-52 PLATE PIVOT ROD
532 42 82-88 E-RING .375
532 18 44-71 SHOULDER SCREW
532 41 08-77 BOTTOM PAN
532 41 66-82 SPRING BRACKET
532 40 26-89 DRIVE PLATE ASSEMBLY
532 41 45-57 IDLER SPRING
532 17 88-28 IDLER SPRING
532 40 25-04 PULLEY SHAFT
532 40 18-20 DRIVE PLATE
532 19 87-91 BEARING
532 40 23-93 PULLEY HALF
817 54 10-08 SCREW 10-24 X .50
532 40 25-11 SPACER BEARING
532 42 29-41 SWING PLATE
532 13 20-10 NUT 3/8-16
532 40 28-78 RETURN SPRING
532 75 11-53 NUT 5/16-18
532 40 89-81 BEARING
873 93 05-00 NUT 5/16-18
532 19 95-09 RUBBER WHEEL PLATE
532 44 06-20 RUBBER RING
532 42 88-67 SCREW 5/16-18 X .750
817 00 05-10 BOLT 5/16-18 X .625
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
31
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
DRIVE
5
8
6
1b
4
7
3
8
1b
6
1a
2
3
5
4
01.03.005-C
KEY
NO.
PART
NO.
DESCRIPTION
1
532 18 82-26 AXLE ASSEMBLY
assy of 1a,1b)
(
1
1
2
3
4
5
6
7
8
a
b
532 17 93-52 AXLE SHAFT
532 18 42-06 ROLL PIN 3/16
532 40 26-91 SPROCKET
532 44 49-49 THRUST WASHER
532 17 98-30 BEARING
817 49 05-08 BOLT 5/16−18 X .500
532 17 12-71 PIN
532 18 92-82 SQUARE KEY
532 12 47-88 RETAINER PIN
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
32
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
CHASSIS / ENGINE / PULLEYS
2
3
2
3
KEY
NO.
PART
NO.
DESCRIPTION
1
01.00.034-A
-
-
580 42 60-01 COMPLETE LCT ENGINE
PW2HK18650178E
1
2
3
532 43 88-40 FRAME
532 15 04-06 BOLT 3/8-16
532 42 88-67 SCREW 5/16-18 X .750
1
KEY
NO.
PART
NO.
DESCRIPTION
1
532 43 88-42 ENGINE MOUNTING PLATE
01.01.004-A
1
KEY
NO.
PART
NO.
DESCRIPTION
1
532 44 30-30 COVER ASSEMBLY
01.21.013-C
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
33
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
CHASSIS / ENGINE / PULLEYS
23
22
14
2
4
21
2
0
11
14
21
19
13
20
18
1
7
1
2
1
4
15
16
6
7
1
0
5
4
8
3
1
2
9
01.21.003-D
KEY
NO.
PART
NO.
KEY
NO.
PART
NO.
DESCRIPTION
DESCRIPTION
1
2
3
4
5
6
7
8
9
532 40 80-07 IMPELLER BELT
532 41 97-44 TRACTION BELT
532 42 92-71 IDLER ARM BRACKET
532 18 05-23 IDLER PULLEY
14
15
16
17
18
19
20
21
22
23
24
532 05 92-89 WASHER
873 80 05-00 NUT 5/16-18
532 85 10-84 SCREW 3/8-24 X 1.375
532 40 00-26 WASHER
532 42 64-91 PULLEY ENG IMPELLER
532 42 64-90 PULLEY ENG TRACTION
874 61 05-16 SCREW 5/16-18 X 1 .00
810 04 05-00 LOCKWASHER 5/16
532 15 54-52 BELT GUIDE
532 42 65-89 NUT 5/16-18
874 78 05-24 SCREW 5/16-18 X 1 .50
532 42 92-70 IDLER BRACKET
817 00 05-10 SCREW 5/16-18 HEX
532 42 42-97 SHOULDERBOLT5/16-18X.500
532 75 11-53 NUT 5/16-18 NYLOCK
532 18 77-86 TRACTION IDLER ARM
532 18 05-22 TRACTION PULLEY
10
11
12
13
811 05 05-00 LOCKWASHER 5/16
532 17 53-31 IDLER BUSHING
874 78 05-20 SCREW 5/16-18 X 1 .00
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
34
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
WHEELS
KEY
NO.
PART
NO.
DESCRIPTION
1
2
532 43 70-83 WHEEL ASSEMBLY LH
532 43 70-84 WHEEL ASSEMBLY RH
1
2
01.06.018-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
35
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
BAG OF PARTS
3
KEY
NO.
PART
NO.
5
DESCRIPTION
4
1
2
3
4
5
6
7
532 19 85-63 POWER CORD
532 16 96-75 RETAINER PIN
532 42 91-12 WRENCH
873 80 06-00 LOCKNUT 3/8−16
819 13 13-16 WASHER 3/8
532 19 20-90 SHEAR BOLT 1/4−20 X 1−3/4
873 80 04-00 LOCKNUT 1/4−20
2
1
7
6
01.14.004-B
KEY
NO.
PART
NO.
DESCRIPTION
1
532 44 30-59 SAFETY IGNITION KEY KIT
1
01.14.009-B
1
3
2
4
1
4
2
01.14.012-B
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
532 18 04-45 SHIFTER ROD TOP
532 18 77-16 SHIFTER ROD BOTTOM
872 27 05-05 CARRIAGE BOLT 5/16-18 X .75
532 15 53-77 NUT 5/16-18
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
36
REPAIR PARTS SNOW THROWER - - MODEL NUMBER 961940010 (96194001003)
DECALS
1
4
9
6
11
1
3
KEY
NO.
PART
NO.
DESCRIPTION
1
3
4
6
9
532 18 10-37 DECAL, DANGER
532 18 10-35 DECAL, DANGER, DEFLECTOR
532 18 10-42 DECAL, DANGER
532 18 10-33 DECAL, INSTRUCTION
581 43 01-01 DECAL, CON RT SPD/LEV/PWST
581 43 01-02 DECAL, CON LT WD/DEF
581 45 59-27 OWNER’S MANUAL, ENGLISH
581 45 60-32 OWNER’S MANUAL, FRENCH
1
-
1
-
-
-
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
37
SERVICE NOTES
38
SERVICE NOTES
39
LIMITED WARRANTY
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi-
als and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or
replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due
to materials or workmanship. This Warranty is subject to the following limitations and exclusions.
1.
This warranty does not apply to the engine, transaxle/transmission components, battery (except as noted below) or com-
ponents parts thereof. Please refer to the applicable manufacturer's warranty on these items.
2.
Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchas-
er. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser un-
less such return is requested by the manufacturer.
3.
Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery which we find
to be defective in manufacture, during the first ninety (90) days of ownership. After ninety (90) days, we will exchange the
Battery, charging you 1/12 of the price of a new Battery for each full month from the date of the original sale. Battery must
be maintained in accordance with the instructions furnished.
4
.
.
The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of original
purchase.
5
This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained in ac-
cordance with the instructions furnished. This Warranty does not apply to any product which has been subjected to altera-
tion, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product.
6
.
.
Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments, standard
hardware and normal maintenance.
7
In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.
Should you have any unanswered questions concerning this Warranty, please contact:
In Canada contact:
HOP
HOP
Outdoor Products Customer Service Dept.
5855 Terry Fox Way
9335 Harris Corners Parkway
Mississauga, Ontario
L5V 3E4
Charlotte, NC 28269 USA
giving the model number, serial number and date of purchase of your product and the name and address of the authorized
dealer from whom it was purchased.
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRAN-
TIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas
do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above limi-
tations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which
vary from locale to locale.
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.
08.09.12 SR
Printed in the U.S.A.